PROFESSIONAL OMNIDIRECTIONAL
CONDENSER MICROPHONE
CM-150
he CM-150 is a ½-inch-diameter
(12.7-mm), omnidirectional electret-
T
condenser microphone. It is intended
for professional recording, free-field mea-
surement and sound-level measurement.
Because of its pre-aged titanium diaphragm,
the CM-150 is extremely stable over a wide
range of environmental conditions.
The CM-150 has a very flat, wide-range fre-
quency response. The mic is supplied with a
proof-of-performance sheet, which shows
frequency response and sensitivity. This
information can be used to calibrate the mi-
crophone. The mic capsule grille fits into a
Bruel & Kjaer 4220 pistonphone or similar
microphone calibrator.
Specifications
Element: Electret condenser.
Fig. 1
Frequency Response
Frequency response (typical): 20 Hz to 20 kHz
1.5 dB (see Fig. 1).
Polar pattern: Omnidirectional (see Fig. 2)
Impedance: 150 ohms, 240 ohms actual, bal-
anced. Recommended minimum load imped-
ance 1000 ohms.
Open circuit sensitivity (48 volt supply): 10.5
mV/Pa* (–39.5 dB re 1 volt/Pa) nominal.
When used for recording, the CM-150
sounds natural and accurate. It preserves
the delicate timbre of acoustic instruments,
yet can reproduce all the power of a pipe
organ. The off-axis response is also smooth,
so any leakage picked up has little colora-
tion.
Power sensitivity: –39.5 dB re 1 mW/Pa.
Equivalent noise level (self-noise): 19 dB SPL
Frequency in Hz
typical, A-weighted (0 dB = .0002 dyne/cm2).
S/N ratio: 75 dB at 94 dB SPL.
Maximum SPL for 3% THD: 127 dB with 48V
phantom power.
Output connector: 3-pin male XLR type.
Power: 18-48 volt phantom power, positive volt-
age on pins 2 and 3 with respect to pin 1.
Self-noise is low, permitting clean record-
ings — especially with close miking. The
mic can handle very loud sounds (127 dB
SPL) without distortion. It is protected
against static and RFI. The output is bal-
anced, low impedance, which allows long
cable runs without hum pickup or high-fre-
quency loss. Powering is by 18-48 volt
phantom power.
Fig. 2
330˚
0˚
30˚
FRONT
-0
300˚
270˚
60˚
90˚
-5
Current drain: 2.7 mA.
-10
Polarity: Positive (inward) pressure on the dia-
phragm produces positive voltage on pin 2 with
respect to pin 3 of the output connector.
Materials: Brass handle, stainless steel mic cap-
sule, titanium diaphragm.
-15
-20
An included foam windscreen reduces wind
noise outdoors.
Finish: Satin black handle and chrome mic cap-
sule.
Architects’ and Engineers’ Specifications
120˚
240˚
OMNI 20 Hz-2 kHz
5 kHz
The microphone shall be a Crown CM-150
or equivalent. It shall be an omnidirectional
electret-condenser type powered by 18-48
volt phantom power. Frequency response
shall be uniform from 20 Hz to 20,000 Hz.
Open-circuit sensitivity shall be 10.5 mV/Pa.
Maximum SPL for 3% THD shall be 127 dB
with 48-volt phantom power. Self-noise shall
be 19 dB SPL A-weighted. Impedance shall
be 240 ohms balanced. The mic shall be
compatible with ½-inch (12.7 mm) indus-
try standard calibration. The Crown CM-
150 is specified.
Dimensions: See Fig. 3.
Weight: 4.48 ounces (127 grams).
10 kHz
20 kHz
REAR
180˚
210˚
150˚
Included accessories: WS-15 foam wind-screen,
carrying pouch, ASA-4 stand adapter and vinyl
grille protector.
Optional accessories: Crown PH-4B phantom
power supply (4 channels, AC powered). Crown
PH-1A phantom power supply (1 channel, bat-
tery or AC powered).
*1 pascal = 10 dynes/cm2 = 10 microbars = 94 dB
SPL.
|
Continental Iron CE23191 User Manual
Continental Iron CP43021 User Manual
Cortelco Conference Phone 879015 TP2 27S User Manual
Crate Amplifiers Musical Instrument CA30 DG User Manual
Dukane Flat Panel Television P42HC User Manual
Dynex Flat Panel Television DX 40L260A12 User Manual
Eagle Electronics Portable Radio EVR 150 User Manual
Fisher Price Video Games R8127 User Manual
GE Oven JKP17 User Manual
GE Washer GCXRP090 User Manual