Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Warning
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
Federal Communication Commission (FCC) Radiation Exposure
Statement
This equipment complies with FCC radiation exposure set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm (8 inches) during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 2.4 GHz
frequency range. FCC requires this product to be used indoors in 2.4 GHz the
frequency range to reduce the potential for harmful interference to co-channel
Mobile Satellite systems.
RSS-210 Compliance Statement
The term “IC:” before the certification/registration number only signifies that
Industry Canada technical specifications were met. Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may
cause undesired operation of the device.
Transmitter Antenna
To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power
(EIRP) is not more than that required for successful communication
This device has been designed to operate with an antenna having a maximum
gain of 5dBi. Antenna having a higher gain is strictly prohibited per regulations
of Industry Canada. The required antenna impedance is 50 ohms.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
Country Code Setting Disable
Country Code selection feature to be disabled for products marketed to the
US/CANADA.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC
OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on
radio equipment and telecommunication terminal Equipment and the mutual
recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station
Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment. All
guidelines of this and of the computer manufacture must therefore be allowed
at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in UK,
Ireland, Germany, France, Spain, Portugal, Italy, Austria, Switzerland, Belgium,
Netherlands, Luxemburg, Denmark, Finland, Norway, Sweden, Poland,
Hungary, Czech, Slovakia, Latvia, Lithuania, Estonia, Slovenia, Greece,
Romania, Bulgaria
EU Countries Not intended for use
None.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause
radio interface, in which case the user may be required to make adequate
measures.
A CE declaration of conformity is available on www.edimax.com
Regulatory Approvals for AC Adapter
Input:
AC 100-240 V, 50-60 Hz
DC 5V, 1.0A
Output:
Power Consumption:
Safety Standards:
EMC:
300mW
UL/CUL 60950-1
FCC part 15 subpart B Class B
Safety Information
For your safety, be sure to read and follow all warning notices and instructions.
•
Do not continue operating if you notice smoke or unusual odors or sounds.
Continued operation may result in electric shock or fire. Immediately turn
off power and remove the power adapter from the outlet, then contact
EPSON.
•
•
Do not disassemble or modify the product in any way (unless described in
instructions). Doing so may cause injury or electric shock.
Make sure you use the power adapter supplied with the MFP Server. Use
of a different power adapter could damage the MFP Server.
Do not handle plugs with wet hands. Doing so may result in electric shock.
Do not use damaged power cords. Doing so may result in electric shock
and fire. Observe the following when handling power cords:
•
•
•
•
•
•
Do not modify power cords.
Do not place heavy objects on power cords.
Do not sharply bend, twist, or pull on power cords.
Do not route power cords near heating equipment.
•
•
Do not attempt to repair the power adapter or cord. Contact EPSON to
order a new one.
Handle power plugs with care. Improper handling may result in fire.
Observe the following when handling power plugs:
•
•
Do not plug in power plugs that are dusty or dirty.
Firmly plug in power plugs all the way.
•
•
Periodically remove power plugs from the outlet and clean the base of the
plug. If power plugs are left plugged into an outlet for long periods, dust
may accumulate near the base, posing a risk of short-circuiting and fire.
To ensure safety, always unplug power adapter from the outlet when the
product will not be used for an extended period.
•
•
Make sure to connect the cables to the correct ports.
Place connecting cables carefully so that no one will step on them or
stumble over them.
•
Avoid locations that are subject to rapid changes in heat or humidity,
shocks or vibrations, or dust.
•
•
Do not expose the device to dampness, dust or corrosive liquids.
Discontinue use if a foreign object or water or other liquid enters the
product. Continued use may result in electric shock and fire. Immediately
remove the power adapter from the outlet and then contact EPSON.
Contents
1. Introduction......................................................................1
2. MFP Server Modes..........................................................2
3. Using Your All-in-one in MAC...........................................4
3.1
3.2
3.3
Printing............................................................................. 6
Scanning.......................................................................... 7
Reading Memory Cards................................................... 9
4. MFP Manager in MAC ...................................................10
4.1
4.2
MFP Server List ............................................................. 10
Option Settings .............................................................. 13
4.2.1
4.2.2
General Setting .................................................................13
Search for MFP Server......................................................14
5. Server Configuration in MAC.........................................15
5.1
5.2
5.3
5.4
5.5
5.6
5.7
Introduction .................................................................... 15
Search for All Available MFP Server .............................. 16
Status of MFP Server..................................................... 17
General Setting.............................................................. 19
TCP/IP Configuration ..................................................... 21
System Configuration..................................................... 22
Wireless Configuration................................................... 23
6. Web Management .........................................................29
6.1
6.2
6.3
Introduction .................................................................... 29
Login .............................................................................. 30
Device Status................................................................. 31
6.3.1
System Status ...................................................................31
Printer Status.....................................................................32
TCP/IP Status....................................................................33
6.3.2
6.3.3
6.4
6.5
Setup Wizard ................................................................. 34
6.4.1
System ..............................................................................34
Wireless ............................................................................37
TCP/IP...............................................................................44
Save Settings ....................................................................45
6.4.2
6.4.3
6.4.4
System Tools.................................................................. 46
6.5.1
6.5.2
Load Default......................................................................46
Upgrade Firmware.............................................................47
7. Troubleshooting .............................................................48
1. Introduction
This MFP Server allows your all-in-one printer to become a shared device on
the network. Unlike many MFP Servers, it can communicate with your
all-in-one printer as if it was connected directly to your computer. This allows
all users to share print, scan, card reader and fax (if available) over the
network. You can also monitor important information such as ink levels.
The MFP Server provides IEEE 802.11g/b wireless LAN connectivity (up to
54Mbps data transfer rate), an Ethernet network port (10/100Mbps Ethernet),
and one USB 2.0/1.1 port. The MFP Server can be connected to your
802.11g/b wireless network or wired network.
1
|