Extron electronic Switch BBG 6 A User Manual

User’s Guide  
BBG 6 A and BBG 6 A J  
Blackburst / Color Bars / Audio Generator  
Extron Electronics, USA  
1230 South Lewis Street  
Anaheim, CA 92805  
800.633.9876 714.491.1500  
FAX 714.491.1517  
Extron Electronics, Europe  
Beeldschermweg 6C  
3821 AH Amersfoort, The Netherlands  
+800.3987.6673 +31.33.453.4040  
FAX +31.33.453.4050  
Extron Electronics, Asia  
135 Joo Seng Rd. #04-01  
PM Industrial Bldg., Singapore 368363  
+800.7339.8766 +65.6383.4400  
FAX +65.6383.4664  
Extron Electronics, Japan  
Kyodo Building, 16 Ichibancho  
Chiyoda-ku, Tokyo 102-0082  
Japan  
68-712-01 Rev. D  
11 06  
+81.3.3511.7655 FAX +81.3.3511.  
© 2006 Extron Electronics. All rights reserved.  
 
警告  
安全须知 中文  
电源 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备  
必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线  
( 地 线 ) 是 安 全 设 施 , 不 能 不 用 或 跳 过 。  
拔掉电源 为安全地从设备拔掉电源,请拔掉所有设备后  
或桌面电源的电源线,或任何接到市电系统的电源线。  
电源线保护 妥善布线, 避免被踩踏,或重物挤压。  
这个符号提示用户该设备用户手册中  
有重要的操作和维护说明。  
这个符号警告用户该设备机壳内有暴  
露的危险电压,有触电危险。  
维护 所有维修必须由认证的维修人员进行。 设备内部没  
有用户可以更换的零件。为避免出现触电危险不要自己  
试图打开设备盖子维修该设备。  
注意  
阅读说明书 用 户 使 用 该 设 备 前 必 须 阅 读 并 理  
解 所 有 安 全 和 使 用 说 明 。  
通风孔 有些设备机壳上有通风槽或孔,它们是用来防止  
机内敏感元件过热。 不要用任何东西挡住通风孔。  
保存说明书 用户应保存安全说明书以备将来使  
用。  
锂电池 不正确的更换电池会有爆炸的危险。 必须使用与  
厂家推荐的相同或相近型号的电池。 按照生产厂的建  
议处理废弃电池。  
遵守警告 用户应遵守产品和用户指南上的所有安  
全和操作说明。  
避免追加 不要使用该产品厂商没有推荐的工具或  
追加设备,以避免危险。  
 
Introduction  
The BBG 6 A and BBG 6 A J (an exclusively Japanese model) are  
compact, high performance blackburst, color bars, and audio  
generators. Unless otherwise noted, the name BBG 6 A refers  
to both the standard (USA and European countries) and the  
Japanese models within this guide.  
The BBG 6 A provides six broadcast quality blackburst signal  
outputs on BNC connectors, two of which can be changed to  
color bars with a DIP switch. For the standard BBG 6 A, the user  
can select output signals as either NTSC or PAL.  
The BBG 6 A J outputs NTSC only and has no setup pedestal in  
its video output. Color bars are standard SMPTE bars (NTSC)  
or full field (PAL). The audio generator provides a single 1  
kHz sine wave audio tone, either balanced or unbalanced,  
with a selectable output level of either +4 dBu (pro) or -10 dBV  
(consumer).  
The BBG 6 A is a member of the VersaTools® line of basic  
distribution amplifiers, switchers, and video accessories. The  
unit ships with an external, desktop 12 V power supply, which  
accepts 100-240 VAC input.  
Models  
There are two available models of the BBG 6 A:  
BBG 6 A (NTSC and PAL signal) — Handles NTSC and  
PAL signals. This version is used in the USA and some other  
countries.  
BBG 6 A J (NTSC signal only) — Handles NTSC signals only.  
This version is used in Japan.  
Other than their differing signal options, these two models are  
identical.  
Installation  
The BBG 6 A can be mounted on a rack shelf (VersaTools or  
universal), under a desk or tabletop, or on a projector bracket.  
Rack mounting  
For optional rack mounting, mount the BBG 6 A on a VersaTools  
19" 1U Rack Shelf (Extron part #60-190-20 or #60-604-20)  
(figure 1) or a standard Universal 1U Rack Shelf (part #60-190-01  
or 60-604-01) (figure 2). On the standard rack shelf, the BBG 6 A  
mounts in one of four locations to the rear of the rack or in one  
of four locations to the front of the rack.  
BBG 6 A • Introduction  
 
Installation  
D
IS  
T
R
IB  
U
T
IO  
D
IS  
T
R
IB  
U
T
IO  
N
A
M
P
L
IF  
IE  
R
D
IS  
T
R
IB  
U
T
IO  
N
A
M
P
L
IF  
IE  
R
D
IS  
T
R
IB  
U
T
IO  
N
A
M
P
L
IF  
IE  
R
D
IS  
T
R
IB  
U
T
IO  
N
A
M
P
L
IF  
IE  
M
D
A
VersaTools Rack Shelf  
R
D
IS  
T
S
N
R
IB  
E
A
U
R
I
L
T
IO  
E
IF  
S
M
P
IE  
R
1/4 Rack Width False  
Front Face Plate  
Figure 2 — Mounting the BBG 6 A on a standard  
shelf  
D
IS  
T
R
IB  
U
T
IO  
N
A
M
P
L
IF  
IE  
R
(2) 4-40 x 3/16" Screws  
Use 2 mounting holes  
on opposite corners.  
Furniture or projector mounting  
Extron  
BBG 6 A  
Furniture mount or projector mount the unit using the optional  
mounting kit (part #70-212-01 for furniture, or 70-217-04 for a  
projector) as follows:  
Black Burst  
Color Bar  
Audio Generator  
1.  
2.  
3.  
If rubber feet were previously installed on the bottom of  
the unit, remove them.  
Figure 1 — Rack mounting the BBG 6 A on a  
VersaTools shelf  
Attach the mounting brackets to the BBG 6 A with the  
machine screws provided (figure 3).  
1.  
2.  
If rubber feet were previously installed on the bottom of  
the unit, remove them.  
For furniture mounting, hold the unit with the attached  
brackets against the underside of the table or other  
furniture. Mark the location of the screw holes of the  
bracket on the mounting surface.  
Mount the unit on the rack shelf, using two 4-40 x 3/16"  
screws in opposite (diagonal) corners to secure the  
BBG 6 A to the shelf.  
3.  
Install blank panel(s) or other unit(s) to the rack shelf.  
Projector  
Mounting  
Bracket  
4.  
Insert the shelf into the rack, aligning the holes in the shelf  
with those of the rack.  
Mounting  
Bolt  
5.  
Secure the shelf to the rack using the supplied machine  
screws. The VersaTools shelf can be mounted in the front  
or in the rear of the rack.  
0
.
1
2
V
A
 M
PO  
A
X
W
/
B
U
D
L
A
B
B
G
R
I
C
K
L
 G
1
E
N
 B
U
R
S
1
 K
H
Z
6
A
1
0
d
E
R
B
V
R
+
4
d
 A
U
A
T
/
T
O
C
P
A
1
2
3
B
u
D
R
O
I
 O
L
O
N
R
B
A
R
C
O
B
L
A
L
O
C
K
B
U
R
S
R
B
A
R
T
/
1
4
1
3
B
L
A
C
K
B
U
R
S
T
Under-Desk  
Mounting  
6
5
Projector  
Mounting  
D
I
S
T
R
I
B
U
T
I
O
N
A
M
P
L
IF  
I
E
R
Projector  
Figure 3 — Desk and projector mounting the BBG 6 A  
BBG 6 A • Installation  
BBG 6 A • Installation  
 
Installation  
4.  
For furniture mounting, drill 3/32" (2 mm) diameter pilot  
holes, 1/4" (6.3 mm) deep in the mounting surface at the  
marked screw locations.  
DIP switch — Use these DIP switches to select between +4 dBu  
(pro) or -10 dBV (consumer) audio output level, between NTSC  
or PAL (USA only) output, and between blackburst or color bars  
for outputs 1 and 2.  
d
5.  
For furniture mounting, insert #8 wood screws into the  
four pilot holes. Tighten each screw into the mounting  
surface until just less than 1/4" (6.3 mm) of the screw head  
protrudes.  
With the first DIP switch set to “+4,” the unit outputs  
+4 dBu audio level with balanced wiring. With the DIP  
switch set to “-10,” the unit outputs -10 dBV audio level  
with unbalanced wiring.  
N
6.  
7.  
8.  
For furniture mounting, align the mounting screws with  
the slots in the brackets and place the unit against the  
surface, with the screws through the bracket slots.  
NTSC  
+4  
RESERVED  
Blackburst  
Blackburst  
+4  
For furniture mounting, slide the unit slightly forward  
or back, then tighten all four screws to secure the unit in  
place.  
ON  
ON  
1
2
3
1
2
3
For projector mounting, secure the unit to a projector  
mount or other surface by inserting the mounting bolt  
through the bracket’s slotted hole.  
-10  
Color bars  
-10  
Color bars  
PAL  
BBG 6 A  
BBG 6 A J  
Figure 5 — BBG 6 A and BBG 6 A J DIP switches  
Connections, Indicators, and Controls  
DIP switch 2 of the BBG A J is not used.  
N
See figure 4 below.  
Please refer to the table below for other combinations.  
N
Power/Signal indicator LED — When illuminated, this LED  
indicates that the BBG 6 A is receiving power.  
a
Output  
Dip  
Switch  
Balanced Unbalanced  
Position  
Blackburst only outputs — Connect up to four display devices  
to these BNC connectors for blackburst output.  
b
+4  
+4 dBu  
-4 dBV  
-2 dBu  
Blackburst/color bars outputs — Connect up to two display  
devices to these BNC connectors for blackburst or color bars  
output.  
c
-10  
-10 dBV  
1
BLACKBURST  
BBG 6 A  
7
BLACKBURST AND AUDIO  
GENERATOR  
1
2
3
4
5
6
POWER  
12V  
.2A MAX  
1 KHZ  
AUDIO  
L
R
ON  
1
2
3
COLORBARS  
6
4
2
5
3
Figure 4 — BBG 6 A front and rear panels  
BBG 6 A • Installation  
BBG 6 A • Connections, Indicators, and Controls  
 
Connections, Indicators, and Controls  
To verify the polarity before connection, plug in the power  
supply with no load and check the output with a voltmeter.  
Audio output connector — Insert a 3.5 mm, 5-pole captive  
screw connector into this connector for a balanced or  
unbalanced 1 kHz sine wave audio tone.  
e
As an alternative, you can use an Extron P/S 100 Universal  
12 VDC Power Supply (part #60-357-01), which can power up to  
ten BBG 6 As or other Extron 12 VDC devices using only one AC  
power connector.  
Do not tin the stripped power supply leads before  
installing the captive screw connector. Tinned wires are  
not as secure in the captive screw connectors and could  
pull out.  
N
Version label — Differentiates the standard (NTSC and PAL  
signals) versus Japanese (BBG 6 A J, NTSC signals only) versions  
of the BBG 6 A.  
g
CAUTION  
For unbalanced audio, connect the sleeve(s) to the ground contact.  
DO NOT connect the sleeve(s) to the negative (-) contacts.  
Specifications  
3/16" (5 mm) MAX.  
Tip  
Ring  
Sleeve (s)  
Tip  
Tip  
NO Ground Here  
Sleeve (s)  
Blackburst output  
Number/signal type..................... 6 blackburst (two can be switched to  
color bars)  
Tip  
NO Ground Here  
Ring  
Balanced Output  
Unbalanced Output  
Connectors ..................................... 6 BNC female  
Standards  
Figure 6 — BBG 6 audio wiring  
Power connector — Plug the external 12 V power supply  
into this 2-pole captive screw connector. The power supply  
is included with the unit. Figure 7 shows how to wire the  
connector.  
BBG 6 A............................... RS-170A standard for NTSC 3.58,  
CCIR 624-4 standard for PAL  
BBG 6 A J............................. RS-170A standard for NTSC 3.58  
Impedance ..................................... 75 ohms  
Sync level  
BBG 6 A............................... 40 IRE for NTSC, 43 IRE for PAL  
BBG 6 A J............................. 40 IRE for NTSC  
Color burst level  
BBG 6 A............................... 40 IRE for NTSC, 43 IRE for PAL  
BBG 6 A J............................. 40 IRE for NTSC  
Setup level  
f
When connecting the power supply, voltage polarity  
is extremely important. Applying power with  
incorrect voltage polarity could damage the power  
supply and the BBG 6 A. Identify the power cord  
negative lead by the ridges on the side of the cord or  
the black heat shrink wrapping around it.  
C
BBG 6 A............................... 7.5 IRE (NTSC) or 0 IRE (PAL)  
BBG 6 A J............................. 0 IRE (NTSC)  
Tolerance for all levels.................. 3%  
Subcarrier levels  
A
A
3/16” (5 mm) MAX.  
+
-
+
-
12 V  
SECTION A–A  
Power Supply  
Output Cord  
Captive Screw  
Connector  
BBG 6 A............................... NTSC 3.579545 3 Hz  
PAL 4.433618 3 Hz  
BBG 6 A J............................. NTSC 3.579545 3 Hz  
Figure 7 — Power connector wiring  
Do not tin the stripped power supply leads before  
N
installing the captive screw connector. Tinned wires are  
not as secure in the captive screw connectors and could  
pull out.  
The two power cord wires must be kept separate  
while the power supply is plugged in. Remove  
power before continuing.  
W
BBG 6 A • Connections, Indicators, and Controls  
BBG 6 A • Specifications, Parts, and Accessories  
 
Specifications, Part Numbers, and Accessories  
Color Bars output  
Number/signal type  
General  
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, 2.5 watts,  
external, autoswitchable; to 12 VDC,  
BBG 6 A............................... 2 color bars, switchable, standard  
SMPTE bars for NTSC,  
1 A, regulated power supply  
full field 8-bar for PAL  
Power input requirements........... 12 VDC, 0.2 A (max.)  
BBG 6 A J............................. Standard SMPTE bars for NTSC  
Connectors ..................................... 2 BNC female  
Standards  
BBG 6 A............................... NTSC 3.58, PAL  
BBG 6 A J............................. NTSC 3.58  
Impedance ..................................... 75 ohms  
Sync level  
BBG 6 A............................... 40 IRE for NTSC, 43 IRE for PAL  
BBG 6 A J............................. 40 IRE for NTSC  
Color burst level  
BBG 6 A............................... 40 IRE for NTSC, 43 IRE for PAL  
BBG 6 A J............................. 40 IRE for NTSC  
Setup level  
Temperature/humidity................ Storage: -40 to +158 °F (-40 t +70 °C) /  
10% to 90%, noncondensing  
Operating: +32 to +122 °F (0° to +50 °C) /  
10% to 90%, noncondensing  
Rack mount.................................... Yes, with optional 1U VersaTools® 3" deep  
rack shelf, part #60-190-20 (RSF 123) or  
60-604-20 (RSB 123); or Universal 9.5"  
deep rack shelf, part #60-190-01 (RSU 129)  
or 60-604-01 (RSB 129). Also under-desk  
mountable with optional MBU 123 kit  
part #70-212-01.  
Enclosure type .............................. Metal  
Enclosure dimensions .................. 1.7" H x 4.3" W x 3.0" D  
(1U high, quarter rack wide)  
4.3 cm H x 10.9 cm W x 7.6 cm D  
(Depth excludes connectors.)  
Product weight .............................. 0.4 lbs (0.2 kg)  
Shipping weight ........................... 3 lbs (2 kg)  
Vibration ........................................ ISTA 1A in carton  
(International Safe Transit Association)  
BBG 6 A............................... NTSC, 7.5 IRE; PAL, 0 IRE  
BBG 6 A J............................. NTSC, 0 IRE  
White level ..................................... 100 IRE  
Tolerance for all levels.................. 3%  
Subcarrier levels  
BBG 6 A............................... NTSC 3.579545 3 Hz, PAL 4.433618 3 Hz  
BBG 6 A J............................. NTSC 3.579545 3 Hz, no setup pedestal  
Listings............................................ UL, CUL  
Compliances................................... CE, FCC Class A, VCCI, AS/NZS, ICES  
MTBF............................................... 30,000 hours  
Audio output  
Number/signal type..................... 1 set (L and R) of stereo sine waves,  
balanced or unbalanced  
Connectors .................................... (1) 3.5 mm captive screw connector, 5 pole  
Impedance ..................................... 50 ohms unbalanced, 100 ohms balanced  
Warranty ........................................ 3 years parts and labor  
All nominal levels are at 10%.  
N
N
Specifications are subject to change without notice.  
Signal level..................................... Selectable: professional level, +4 dBu  
(1.23 V) balanced; or consumer level,  
-10 dBV (316 mV) unbalanced  
THD................................................. 0.1%  
Tolerance for all levels.................. 3%  
Signal frequency ........................... 1 kHz  
0 dBu = 0.775 V, 0 dBV = 1 V, 0 dBV 2 dBu.  
N
BBG 6 A • Specifications, Parts, and Accessories  
BBG 6 A • Specifications, Parts, and Accessories  
 

Extron electronic Network Card HSA 200S Series User Manual
Field Controls Water Pump 20+UL User Manual
Fisher Price Baby Toy B8078 User Manual
Frigidaire Air Conditioner 309000834 User Manual
Fujitsu Laptop S6231 User Manual
Fujitsu Server BX900 S1 User Manual
GE Toaster 681131690966 User Manual
GE Washer S2000 User Manual
Gianni Industries Door 10020 User Manual
Giant Septic System MP4130HTC User Manual