GE Outdoor Timer 15057 1 User Manual

- Weekdays only (MO TU WE TH FR)  
- Weekends only (SA SU)  
Digital Timer  
3. Press the HR and MIN buttons to select the time of day to turn the  
Timer ON press the HR button repeatedly to change from AM to PM.  
15057-1  
7/15/09  
4. Press the PROG button again. The display will read:  
DO NOT EXCEED THE RATING OF THE TIMER 1000 WATTS FOR  
GENERAL PURPOSE AND TUNGSTEN LOAD (SUCH AS LIGHTING).  
THIS TIMER IS FOR INDOOR USE ONLY. DO NOT USE IN WET  
LOCATIONS.  
It will show current settings if it has been previously set.  
5. Repeat steps 2 and 3 to program other events.  
THIS TIMER HAS A BUILT-IN RECHARGEABLE BATTERY THAT IS  
USED TO RETAIN THE CURRENT TIME AND ON/OFF SETTINGS  
WHEN THE UNIT IS NOT PLUGGED IN AN OUTLET.  
6. To set additional ON and OFF cycles (maximum of 7 events) press the  
PROG button and follow the procedures 2-5 above for each new ON/OFF  
event. When you are finished press the CLK button the display will now  
show the current time and the Timer will control the device plugged into it  
according to the programmed events.  
IN CASE OF A FAILURE OF THE TIMER. PRESS THE RESET BUTTON  
TO RESTART THE TIMER.  
REVIEWING EVENTS  
TO ACTIVATE YOUR TIMER  
Press the PROG button repeatedly and will cycle through  
all the programmed ON/OFF events. Press the CLK to return  
to normal operation.  
1. Display - Remove the plastic film from display.  
2. Installation - Plug the timer into a grounded outlet and wait for at least  
30 minutes to charge the built-in rechargeable battery. Once the battery  
has charged, unplug and press the “RESET” button.  
CLEARING PROGRAMMED EVENT  
Press the PROG button repeatedly to find the ON/OFF event you want to  
clear. While holding the MODE button down, press the PROG to clear the  
settings for the event.  
3. Set Current Time - While holding down the CLK (Clock) button, press  
the DAY, HR (Hour) and MIN (Minute) buttons to set the day, hour and  
minute. Note the AM or PM appears after the time.  
ACTIVATING YOUR EVENTS  
4. Release the CLK (Clock) button.  
Automatic - For controlled operation according to programmed events,  
press the MODE button repeatedly until AUTO is displayed.  
Your Timer is now ready to be programmed.  
PROGRAMMING AN EVENT  
Random - For random operation press the MODE button until RDM  
is displayed. The Timer will turn ON and OFF at +/- 30 Minutes of  
programmed events randomly.  
1. Press the PROG button once. The display will read  
Manual - For manual operation, press the MODE button until ON  
(to turn and remain on) or OFF (to turn and remain off) is displayed.  
or if an event has already been programmed the current event will be  
displayed. It will show current settings if it has been previously The  
number 1 indicates that you are now programming Event until the day you  
choosen to program is displayed.  
OPERATING THE TIMER  
Plug the Timer into an outlet near where you want time your lighting or  
appliance. Plug the lighting or appliance into the Timer. Check and adjust  
the Timer setting if needed.  
2. To select the day to be programmed press the DAY button repeatedly  
the display should show the day on which you want the timer to turn ON.  
The day options includes:  
is a trademark of the General Electric Company and is used under license to  
Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114.  
- All days of the week (MO TU WE TH FR SA SU)  
- Any single day of the week (for example WE)  
This Jasco product comes with a 1 year limited warranty.  
 

Eizo Computer Monitor EV2216W User Manual
Elation Professional Stereo Receiver AR 32RM User Manual
Excalibur electronic Games 370G User Manual
Extron electronic Stereo Receiver VS50 SL User Manual
Faber Ventilation Hood 620000362 User Manual
Fiat Lawn Mower T833O User Manual
Fisher Price Motorized Toy Car 74540 9993 User Manual
Garland Oven BS CX User Manual
GE Microwave Oven JEB1860DMCC User Manual
GE Monogram Oven ZET2RM User Manual